Anonymous ID: ed08de Feb. 15, 2021, 8:06 p.m. No.12941394   ๐Ÿ—„๏ธ.is ๐Ÿ”—kun   >>1402 >>1405

>>12941341

look

I am not telling you to run out and buy one

but a benchtop milling machine is a good investment

will fit in anyone's home garage on a (gasp) benchtop

 

various manufacturers and models to choose from

 

the Enco are nice

so are the Seig's

 

machining is fun

and the resources on line are amazing

Anonymous ID: ed08de Feb. 15, 2021, 8:24 p.m. No.12941566   ๐Ÿ—„๏ธ.is ๐Ÿ”—kun   >>1587

>>12941498

>only real way to do it is with an endmill

actually

 

it depends on the 80% you start with

and it depends on the Jig that you get to do the finishing

 

I have seen "80%" receivers with the mag well AND the trigger pocket already milled out

 

all you need to do to finish it is drill three holes from the side (using a high quality steel jig with accurate drill bushings)

 

AND then the slot for the trigger itself to poke out the bottom of the trigger pocket

 

again, drilled through the jig

one hole at each end of the slot with the correct size drill but

 

then you connect the holes into a "slot" using a carbide bur in a rotary tool

finishing up with a file

 

same thing when you go to "fit" all the parts into your receiver

 

and persuading that needs to be done for things to fit appropriately can usually be accomplished with the rotary tool (dremel) and some judicious use of files

Anonymous ID: ed08de Feb. 15, 2021, 8:36 p.m. No.12941629   ๐Ÿ—„๏ธ.is ๐Ÿ”—kun

>>12941587

having a machine shop myself

and having dabbled a bit in both

airsoft and "conventional" firearms

it is surprising how similar their manufacture can be when one attempts to achieve the narrow end of the accuracy spectrum in either case

 

accurate machining, and accurate assembly are required for an accurate rifle

 

regardless of the projectile that comes out of the bore

Anonymous ID: ed08de Feb. 15, 2021, 8:39 p.m. No.12941645   ๐Ÿ—„๏ธ.is ๐Ÿ”—kun   >>1670 >>1735

>>12941587

>Now let's talk about the milling specs for a real gun.

kek

I was still reminiscing about the Bernoulli Principle, and the finer points of tuning ones hop-op mechanism

 

just how "tight" to go on a tight-bore barrel

and weather I should use .25gram bb's or .28grams todayโ€ฆ (is that a light wind I senseโ€ฆ)

Anonymous ID: ed08de Feb. 15, 2021, 9:05 p.m. No.12941853   ๐Ÿ—„๏ธ.is ๐Ÿ”—kun   >>1910

>>12941824

>Well lets see. What happened to 8chan? Why does it no longer exist?

because Frederick Brennen and Travis View went on a #Cancel campaign targeting CloudFlare, the supplier of DDoS protection for 8chan

 

their cancel campaign succeeded

even though the shooting was livestreamed on facebook

and the manifesto was first posted on instagram

 

so how the fuck do facts even matter anon?

Anonymous ID: ed08de Feb. 15, 2021, 9:10 p.m. No.12941889   ๐Ÿ—„๏ธ.is ๐Ÿ”—kun

>>12941870

>Does it even fucking matter if the manifesto false flag was posted on another board and copied to qresearch?

no

it doesn't

bitches will do what they want

so

if it doesn't matter

then tell me why it matters that we are posting about 80% receivers?

 

logic kind of just fell apart didn't it?

Anonymous ID: ed08de Feb. 15, 2021, 9:15 p.m. No.12941935   ๐Ÿ—„๏ธ.is ๐Ÿ”—kun

>>12941910

>Anything, literally anything can be used as an excuse to end this board, but when you see such obvious attempts it's important to call them out so others can see what's being done and understand why.

that logic doesn't follow